|
Title: Microchip PICKIT 2 Clone - Schematic+PCB (PROTEUS) Post by: chyelim on September 01, 2007, 03:04:39 03:04 Hi, guys, there is lower version for ICD 2. The PICKIT2. PICKIT2 now support in MPLAB 7.62 the latest version. Using MPLAB, it support less model of PICs but if using the software from Microchip, the PICKIT2 software then will support more PICs. There is only one problem, it is not support FUSES CONFIGURATION change but Microchip release the source code so have to modify ourselves. Thanks! Enjoy!
Here is the PICKIT2 Clone link: http://www.linkbucks.com/link/fa88da72/6322 Sonsivri is the BEST !! Title: Re: Microchip PICKIT 2 Clone - Schematic+PCB (PROTEUS) Post by: Kesitinh on September 01, 2007, 06:08:55 06:08 Thank U !
Title: Re: Microchip PICKIT 2 Clone - Schematic+PCB (PROTEUS) Post by: Kova on September 01, 2007, 06:22:55 06:22 Sorry but the .hex for the PIC? :-[
Title: Re: Microchip PICKIT 2 Clone - Schematic+PCB (PROTEUS) Post by: olotill on September 01, 2007, 06:55:35 06:55 Thanks for your sharing mate but please can you explain if I can modify fuses config with PICKIT2...
Thanks for your time.. Best Regards Title: Re: Microchip PICKIT 2 Clone - Schematic+PCB (PROTEUS) Post by: chyelim on September 01, 2007, 05:22:05 17:22 Sorry but the .hex for the PIC? :-[ Here is the firmware : http://www.linkbucks.com/link/f9502d13/6322 Here is the flash software source code in C# : http://www.linkbucks.com/link/fca86c41/6322 Title: Re: Microchip PICKIT 2 Clone - Schematic+PCB (PROTEUS) Post by: protection on September 01, 2007, 09:19:15 21:19 Thank you for sharing guy, I try it :)
Title: Re: Microchip PICKIT 2 Clone - Schematic+PCB (PROTEUS) Post by: aliuzun2004 on September 01, 2007, 11:19:13 23:19 Sorry but the .hex for the PIC? :-[ also microchip gives firmware and source code. http://www.microchip.com/stellent/idcplg?IdcService=SS_GET_PAGE&nodeId=1406&dDocName=en023805 Title: Re: Microchip PICKIT 2 Clone - Schematic+PCB (PROTEUS) Post by: shobhitkukreti on September 02, 2007, 04:57:50 04:57 there are many popular icd2 clones available which work well,both the serial and usb version, so what is different about the pickit
Title: Re: Microchip PICKIT 2 Clone - Schematic+PCB (PROTEUS) Post by: chyelim on September 02, 2007, 05:13:25 05:13 there are many popular icd2 clones available which work well,both the serial and usb version, so what is different about the pickit Hi, ICD2 is in circuit debugger, it can program and debugger almost all the Microchip MCU but PICKIT2 is different. It can only program almost all the Microchip MCU but debug a few range of Microchip MCU. As a conclusion, PICKIT2 design is simple than ICD2. You can have a details at this both site http://www.microchip.com/icd2 http://www.microchip.com/pickit2 Title: Re: Microchip PICKIT 2 Clone - Schematic+PCB (PROTEUS) Post by: aliuzun2004 on September 03, 2007, 12:15:02 12:15 there are many popular icd2 clones available which work well,both the serial and usb version, so what is different about the pickit www.icd2clone.com potyo2 is good icd2 clone. it is programming pic24fxxx series. Many icd2 clones don't programme / debug 3.3 v pic. rs232 icd2 clone is very very slow. Title: Re: Microchip PICKIT 2 Clone - Schematic+PCB (PROTEUS) Post by: chyelim on September 04, 2007, 08:09:20 08:09 Thanks for your sharing mate but please can you explain if I can modify fuses config with PICKIT2... Thanks for your time.. Best Regards Hi, olotill, sorry for the late reply, the fuses configuration is still limited. We have to manually modify the source code. Title: Re: Microchip PICKIT 2 Clone - Schematic+PCB (PROTEUS) Post by: chyelim on September 06, 2007, 03:15:33 03:15 Hi, guys !! a good news for those who using PICKIT2. Microchip had launched the latest MPLAB 7.62 which can support more PICs but compare with the real PICKIT2 is still far. There is only a weakness in PICKIT2 software is the fuses configuration cannot be change. Thanks !!
Title: Re: Microchip PICKIT 2 Clone - Schematic+PCB (PROTEUS) Post by: pickit2 on September 09, 2007, 12:28:43 00:28 By default MPlab has the config fuses set to load from your code. So untick the "Configuration Bits set in code." found in the Configure menu top bar. then you have controll over setting the config bits.
BillyW Title: Re: Microchip PICKIT 2 Clone - Schematic+PCB (PROTEUS) Post by: charudatt on June 25, 2009, 06:09:43 18:09 which gerber viewer would open the files in the zip. any luck with .ps files instead.
Title: Re: Microchip PICKIT 2 Clone - Schematic+PCB (PROTEUS) Post by: hamid9543 on August 01, 2013, 03:29:01 15:29 File not found!
can everyone upload again. thx Title: Re: Microchip PICKIT 2 Clone - Schematic+PCB (PROTEUS) Post by: bbarney on August 01, 2013, 05:07:07 17:07 File not found! can everyone upload again. thx WHAT FILE ? on this OLD THREAD are you looking for ? the last entry was over 4 years ago ! |