Recent Posts

no matter on what i try i get the same results with a .4' x .5" size
the drill seems to be the right i measured and there are 100mils between the ic pad drills

well i have gotten the files using my first try with netlist and so am satisfied with
those, i never fiddled with gerbers before so this is all not famliar to me

new screenshot

Close but no cigar I would say Well in this case the Gerber files is in English units
The settings are
2:3
English
Absolute
none
When importing you can select several files as long as the setting is the same
So go to tables->Layers and do this
and tables->Layers Order and do this (think about it looking at the PCB from above)
First at this point you will be able to extract the netlist

new screenshot

this what i get when importi the drill file

This file should work. At the time of importing. You MUST check the units. Camtastic if full of bugs and this is one of them.
So the units dialog you should use is this
Digits 3:4
Units Metric
Zero Supression None
Type Absolut

this what i get when importi the drill file

[Country]

Country	italia
Note	mastercam

May be this website will provide maximum support for designing Audio system with various projects since 2001

Welcome to ESP, the home of DIY audio and electronics articles, and PCBs for popular projects.  Electronics is a wonderful hobby, and with DIY there is a huge scope to get the best performance for less money than otherwise.  DIY is fun and educational, and by building your own audio equipment, you get to learn electronics as well as build equipment that may cost a great deal more in the shops.  ESP is committed to providing high quality projects that are known to work, printed circuit boards (PCBs) for the most popular projects, and to assist you if necessary to complete or debug your project.  There is a very wide range of power amplifiers, preamps, guitar/ bass amplifiers, studio equipment, effects, and other projects to build, including loudspeakers, subwoofers, and many others.

https://sound-au.com/index.html

i trying to make a netlist i got so far, i am get"Netlist extraction error: no tools defined in NC tools table. Please define the tools before proceeding."
seems to be the drill file but whatever i choose i cant come past this one

any suggestions

just for s n giggles i change d the layers to solder paste layer and i got past the error now got i netlist
but i think a drill file is needed or this needs to be done manually place pads

at least i can export to pcb

since this is the first time doing in am really not sure what i am doing

but i a couple of days i will be a suppa duppa mastah on rev eng

i am attaching the files i got so far

i just renamed the file so i could remember which one was what

the issues i got now is that i got only top and bottom layear but i see the top overlay but its not shown, gotta figure out this one now
i tried to export and then import the layers but this did not work it just added the layers i manually added but still not showing all other layers

i think i messed up on this one seems the board is like .4 x .56 inches big and to my knowledge there are no miniature cmponents on this board
back to the drawing board

that looks he(two hockeysyicks) of alot better than to thoe i looked at from the original files, i did a lot of work unessesary

but i still pretty much a newb with pcb design, no i need to figure out what aperture is and what it does.

can you just explain wht is the difference between G0 and G2 file they look kinda the same

and i am going to get gerbview to see what it can do, seen it but not used it

G0 G2 one of those is bottom overlay and the other one is the drill file is my guess

did you get the gerber files to work ?

Well yes or no I got them to work partly. The aperture values was 10 times to big. But using the unit tenths(1/10000 inch) all worked perfectly. The drl file has also the same problem. Everything is then times bigger than it should