Sonsivri
 
*
Welcome, Guest. Please login or register.
Did you miss your activation email?
August 31, 2025, 05:26:25 05:26


Login with username, password and session length


Pages: [1]
Print
Author Topic: Make your own current measuring sensor  (Read 1948 times)
0 Members and 3 Guests are viewing this topic.
safkans
Inactive

Offline Offline

Posts: 6

Thank You
-Given: 5
-Receive: 0


« on: July 23, 2025, 07:24:51 19:24 »

If you're familiar with the SCT-013 series sensors, I'd like to build an equivalent sensor myself. How should I proceed? I'd appreciate your advice.
Logged
Sideshow Bob
Cracking Team
Hero Member
****
Offline Offline

Posts: 1027

Thank You
-Given: 235
-Receive: 1006



« Reply #1 on: July 23, 2025, 07:40:43 19:40 »

In what range of current do you want to measure is it AC or DC. I also see you only have two posts. How well are you into the arts of electronics. Just so I can adjust how I/We may help you   
Logged

I have come here to chew bubblegum and kick ass... and I'm all out of bubblegum
sphinx
Hero Member
*****
Offline Offline

Posts: 932

Thank You
-Given: 630
-Receive: 288



« Reply #2 on: July 23, 2025, 08:33:45 20:33 »

Sorta looks like a university thesis project, if you were somewhat into electronics you would already know that it is a current transformer with a load built in hence the 1V output.

A split core type is more calculations compared to a non-split.

You want help with something let the users on sonsivri do all the guessing and figuring stuff out!
Logged

laws of physics are not laws at all, just assumptions and formulas that work as long as we don't figure something new that wrecks the calculations. the infinite onion try to peel that one
safkans
Inactive

Offline Offline

Posts: 6

Thank You
-Given: 5
-Receive: 0


« Reply #3 on: July 23, 2025, 08:39:15 20:39 »

I want to measure AC current. I'm developing a home-use application. I've previously worked with flyback transformers at high frequencies like 3 kHz. I'm not exactly an amateur in this field. What I want is to produce a current-measuring sensor with a minimum cost, up to 30 amps. This might be outside the scope of traditional transformer logic. Who knows? I'm open to your ideas, Sonsivri members.
Logged
sphinx
Hero Member
*****
Offline Offline

Posts: 932

Thank You
-Given: 630
-Receive: 288



« Reply #4 on: July 24, 2025, 05:37:52 05:37 »

well the cheapest one is wire wound around the cable where you want to measure your current
Logged

laws of physics are not laws at all, just assumptions and formulas that work as long as we don't figure something new that wrecks the calculations. the infinite onion try to peel that one
sadman
Hero Member
*****
Offline Offline

Posts: 736

Thank You
-Given: 1924
-Receive: 3061


Sow The Seeds of Love


« Reply #5 on: July 24, 2025, 05:48:14 05:48 »

this type of sensor normaly based on linear hall effect senser and a coil wound around a ferrite or iron core i have some deisn and application note share once back home in evening
Logged
Sideshow Bob
Cracking Team
Hero Member
****
Offline Offline

Posts: 1027

Thank You
-Given: 235
-Receive: 1006



« Reply #6 on: July 24, 2025, 07:10:02 07:10 »

If you are on a budget why not get some clones from China. I can see it would be fun to try to make by all means. But probably more expensive than a clone in the end
https://www.aliexpress.com/item/1005006849016531.html
https://www.aliexpress.com/item/32962211649.html
Logged

I have come here to chew bubblegum and kick ass... and I'm all out of bubblegum
sadman
Hero Member
*****
Offline Offline

Posts: 736

Thank You
-Given: 1924
-Receive: 3061


Sow The Seeds of Love


« Reply #7 on: July 24, 2025, 04:04:03 16:04 »

If you're familiar with the SCT-013 series sensors, I'd like to build an equivalent sensor myself. How should I proceed? I'd appreciate your advice.

Same technique or topology used in these types of sensors (SCT-013) as described in attached article and application note hope this this will helpfull for you and friends here.

« Last Edit: July 25, 2025, 04:58:07 16:58 by sadman » Logged
safkans
Inactive

Offline Offline

Posts: 6

Thank You
-Given: 5
-Receive: 0


« Reply #8 on: July 26, 2025, 12:23:39 00:23 »

Thank you for your valuable information. The information in the PDFs was especially helpful.

Posted on: July 26, 2025, 12:21:33 00:21 - Automerged

If you are on a budget why not get some clones from China. I can see it would be fun to try to make by all means. But probably more expensive than a clone in the end
https://www.aliexpress.com/item/1005006849016531.html
https://www.aliexpress.com/item/32962211649.html


Of course. Just a curiosity.
Logged
Pages: [1]
Print
Jump to:  


DISCLAIMER
WE DONT HOST ANY ILLEGAL FILES ON THE SERVER
USE CONTACT US TO REPORT ILLEGAL FILES
ADMINISTRATORS CANNOT BE HELD RESPONSIBLE FOR USERS POSTS AND LINKS

... Copyright © 2003-2999 Sonsivri.to ...
Powered by SMF 1.1.18 | SMF © 2006-2009, Simple Machines LLC | HarzeM Dilber MC