Sonsivri
 
*
Welcome, Guest. Please login or register.
Did you miss your activation email?
February 23, 2018, 01:34:17 13:34


Login with username, password and session length


Pages: [1]
Print
Author Topic: AT89C55WD programmer  (Read 414 times)
0 Members and 1 Guest are viewing this topic.
mr_byte31
Hero Member
*****
Offline Offline

Posts: 559

Thank You
-Given: 52
-Receive: 144



« on: February 05, 2018, 11:50:40 11:50 »

Hi All,

I am looking for a simple programmer for AT89C55WD so I can build it.
I searched the internet but couldn't reach any valuable information. there is only one programmer at microchip website which is really expensive to me.
I also found a parallel programmer on internet but my PC doesn't support this interface anymore.
any suggestions ?
Logged

Do not trifle with the Moderators , as you are small, and crunchy, and taste good with ketchup.
pickit2
Moderator
Hero Member
*****
Offline Offline

Posts: 4062

Thank You
-Given: 627
-Receive: 2254


There is no evidence that I muted SoNsIvRi


« Reply #1 on: February 05, 2018, 03:00:14 15:00 »

the MiniPro TL866 is cheap
Logged

Note: Did you buy a $5 key to by-pass a please invite me request   Then you forget to post in the forum, then your account maybe resticted
mr_byte31
Hero Member
*****
Offline Offline

Posts: 559

Thank You
-Given: 52
-Receive: 144



« Reply #2 on: February 13, 2018, 03:09:56 15:09 »

making the circuit will be much cheaper !
did you try any circuits for this controller?
Logged

Do not trifle with the Moderators , as you are small, and crunchy, and taste good with ketchup.
kayvee
Active Member
***
Offline Offline

Posts: 151

Thank You
-Given: 86
-Receive: 90


« Reply #3 on: February 13, 2018, 04:11:25 16:11 »

I'd agree with pickit2, the MiniPro is a good way to go.

Then you can use it on any other future project that comes along.
Logged
pickit2
Moderator
Hero Member
*****
Offline Offline

Posts: 4062

Thank You
-Given: 627
-Receive: 2254


There is no evidence that I muted SoNsIvRi


« Reply #4 on: February 13, 2018, 05:35:16 17:35 »

Quote from: mr_byte31
making the circuit will be much cheaper !
did you try any circuits for this controller?
Why ?
It is cheaper to buy the MiniPro TL866cs and upgrade it to TL866A
plus you get all the adapters thrown in.
Logged

Note: Did you buy a $5 key to by-pass a please invite me request   Then you forget to post in the forum, then your account maybe resticted
towlerg
Active Member
***
Offline Offline

Posts: 179

Thank You
-Given: 336
-Receive: 77

What is this for?


« Reply #5 on: February 13, 2018, 07:50:47 19:50 »

Whats the difference between TL886cs and TL866A, seem the same on aliexpress.com?

The only supported device I could finf did not include any of the 18FxxKxx series, did I miss something?
Logged

Win 7 Ult x64 SP1 on HP2570p
sphinx
Hero Member
*****
Offline Offline

Posts: 582

Thank You
-Given: 288
-Receive: 135



« Reply #6 on: February 13, 2018, 08:50:13 20:50 »

the TL866A has a icsp port TL866CS does not, but is upgradeable to a TL866A if wanted to do
some extra work to change firmware and adding a icsp connector.
Logged

the more you learn, the lesser you get to understand. is it then good know alot but not understand what you know or.......
pickit2
Moderator
Hero Member
*****
Offline Offline

Posts: 4062

Thank You
-Given: 627
-Receive: 2254


There is no evidence that I muted SoNsIvRi


« Reply #7 on: February 14, 2018, 11:57:35 11:57 »

The only supported device I could finf did not include any of the 18FxxKxx series, did I miss something?
The 18FxxJxx and 18xxKxx are programed the same way. the K devices are just newer.
But then you do have a Pic Programmer, don't you. if your using Pic devices other than just the one off.

For a list of devices is here. Note: there maybe a newer list of devices. wink or add your own devices, if you know where to look.
http://www.autoelectric.cn/minipro/miniprosupportlist.txt
« Last Edit: February 14, 2018, 12:01:29 12:01 by pickit2 » Logged

Note: Did you buy a $5 key to by-pass a please invite me request   Then you forget to post in the forum, then your account maybe resticted
towlerg
Active Member
***
Offline Offline

Posts: 179

Thank You
-Given: 336
-Receive: 77

What is this for?


« Reply #8 on: February 14, 2018, 04:37:58 16:37 »

Quote
The 18FxxJxx and 18xxKxx are programed the same way. the K devices are just newer.
I guess that true in principle (modified SPI) it doesn't seem to be true in detail. In their infinite wisdom, Microchip have issued separate programming specs for the J and K series.

I have bought a Pickit3 specifically because it claims to support 18F26K42. If I could find a PK2DeviceFile.dat with 18F26K42 (although I did find for 18F26K22) I'd stick with my trusty Pickit2.
Logged

Win 7 Ult x64 SP1 on HP2570p
Yukine
Newbie
*
Offline Offline

Posts: 11

Thank You
-Given: 10
-Receive: 14


« Reply #9 on: February 17, 2018, 05:31:03 17:31 »

just asking, why are you using a 89c55

also, this one seems simple enough to build (this should work with a serial <-> usb converter)
http://www.shrubbery.net/~heas/willem/8051-avr2/index-9.htm
Logged

Pages: [1]
Print
Jump to:  


DISCLAIMER
WE DONT HOST ANY ILLEGAL FILES ON THE SERVER
USE CONTACT US TO REPORT ILLEGAL FILES
ADMINISTRATORS CANNOT BE HELD RESPONSIBLE FOR USERS POSTS AND LINKS

... Copyright 2003-2999 Sonsivri.to ...
Powered by SMF 1.1.18 | SMF © 2006-2009, Simple Machines LLC | HarzeM Dilber MC