mbed to Keil uVision5

[rBot]

Hi everyone,

Is there a guide of some sort that explains, in detail (as I obviously need it), how to set up set up uVision 5 to work properly with an ARM STM32F411RE (Nucleo board)?  Like others have stated, the more I read, the more confused I get.   I thought I had it figured out, but apparently not.  How do you know if you are using the right toolchian and have it installed correctly?

Thanks

[Ichan]

Not in detail, install MDK5 software pack for STM32F4 and Nucleo board - some samples in there.

MDK5 Legacy Support may need to be installed too, for the sample codes.

-ichan

[rBot]

Still can't seem to get uVision to work. . .

I have a STM32F411RE Nucleo board.  I can compile and run the 'Blink-LED' program just fine on mbed.  I'm using uVision 5.13.  When I export the 'Blink-LED' program and try to compile it in uVision, I get the following errors:

Build target 'mbed NUCLEO_F411RE'
compiling main.cpp...
Error: C9511E: Product definition file was not found. The following paths were searched:
 - C:\Keil_v5\ARM\ARMCC\Bin\mdk_cm_pro.elmap
 - C:\Keil_v5\ARM\ARMCC\Bin\..\..\sw\mappings\mdk_cm_pro.elmap
 - C:\Keil_v5\ARM\ARMCC\Bin\..\..\..\sw\mappings\mdk_cm_pro.elmap
 - C:\Keil_v5\ARM\ARMCC\Bin\..\sw\mappings\mdk_cm_pro.elmap
Error: C9545E: Info key CT.ProductName could not be found in product definition C:\Keil_v5\ARM\ARMCC\sw\mappings\armcompiler.elmap
Product: unknown
Component: ARM Compiler 5.05 update 1 (build 106)
Tool: ArmCC [4d0efa]
linking...
.\build\Nucleo_blink_led.axf: Error: L9511E: Product definition file was not found. The following paths were searched:
 - C:\Keil_v5\ARM\ARMCC\Bin\mdk_cm_pro.elmap
 - C:\Keil_v5\ARM\ARMCC\Bin\..\..\sw\mappings\mdk_cm_pro.elmap
 - C:\Keil_v5\ARM\ARMCC\Bin\..\..\..\sw\mappings\mdk_cm_pro.elmap
 - C:\Keil_v5\ARM\ARMCC\Bin\..\sw\mappings\mdk_cm_pro.elmap
.\build\Nucleo_blink_led.axf: Error: L9545E: Info key CT.ProductName could not be found in product definition C:\Keil_v5\ARM\ARMCC\sw\mappings\armcompiler.elmap
Product: unknown
Component: ARM Compiler 5.05 update 1 (build 106)
Tool: armlink [4d0efa]
Finished: 1 information, 0 warning and 2 error messages.
".\build\Nucleo_blink_led.axf" - 2 Error(s), 0 Warning(s).
Target not created.

I have the following 'packs' installed:
 ARM::CMSIS
Keil:: MDK-Middleware
Keil::STM32F4xx_DFP
Keil::STM32NUCLEO_BSP

If someone could point me in the right direction, I'd greatly appreciate it.

Thanks,
Duane

[Ichan]

I just notice that the need is to porting in mbed project, never use that one.

A quick googling found this on Keil website: Porting an mbed Project to MDK-ARM, did not read it as i have no interest.

-ichan

[CHJAY]

I have just checked my environment.
please try to install  package "Keil:ARMCortex-DFP".

I use uVision 5.12.0.0 and LPC1114/1115 tho.

chjay