Sonsivri
 
*
Welcome, Guest. Please login or register.
Did you miss your activation email?
December 04, 2016, 03:16:33 15:16


Login with username, password and session length


Pages: [1]
Print
Author Topic: Alarm done at ISIS Proteus has keyboard and LCD  (Read 1867 times)
0 Members and 1 Guest are viewing this topic.
ratoseco
Junior Member
**
 Muted
Offline Offline

Posts: 36

Thank You
-Given: 55
-Receive: 18


« on: June 03, 2012, 12:22:10 00:22 »

Friends need help to run the circuit in Proteus ARES, because I have many difficulties, someone help me?
 thank you.
 Alcindo
 
Logged
jeanninemtv
Senior Member
****
Offline Offline

Posts: 315

Thank You
-Given: 57
-Receive: 25


« Reply #1 on: June 04, 2012, 07:52:15 07:52 »

hello

which are your problems with?  could you specify?  or do you need the whole board to be done?
Logged
ratoseco
Junior Member
**
 Muted
Offline Offline

Posts: 36

Thank You
-Given: 55
-Receive: 18


« Reply #2 on: June 04, 2012, 08:51:42 20:51 »

Hello Jeannine.

I would like to ask your help to draw the circuit that you already did on Isis, but on Ares.
So, putting it simple, transfer it from Isis to Ares, because I have some difficulties working with this programme and doing the PCB.
I'm from Portugal, you may not remember me, but we used to exchange some opinions regarding electronics before you went to France.
Thanks in advance for all the help you're providing me.

Best regards.
Alcindo
 
Logged
ratoseco
Junior Member
**
 Muted
Offline Offline

Posts: 36

Thank You
-Given: 55
-Receive: 18


« Reply #3 on: June 13, 2012, 01:50:37 01:50 »

Friends need help to run the circuit in Proteus ARES, because I have many difficulties, someone help me?
 thank you.
 Alcindo
 
Logged
CocaCola
V.I.P
Senior Member
*****
Offline Offline

Posts: 397

Thank You
-Given: 108
-Receive: 182


« Reply #4 on: June 13, 2012, 06:40:07 06:40 »

May I asked what problems and difficulties you are having?  It's likely more beneficial to work out those problems and let you wrap it up vs having someone else...  It's a pretty simple circuit, overall and wouldn't be hard to redo in any PCB layout package from scratch either, if you must...

The steps are pretty straight forward, you need to Netlist it to ARES, pick the packages for the components (you will be prompted to do this), layout the board size and edge, set the design rules for the board,  auto place the parts (and then clean up the bone head auto placing), auto route the board (ignore the bone head routing at this point) review the entire thing at this point and decide if you should undo the auto route and reposition anything before routing again, once you are satisfied with the final component layout, you can fine tune the routing (there will be bone head routing that can be manually cleaned up) and silk screen...
« Last Edit: June 13, 2012, 06:42:57 06:42 by CocaCola » Logged
Pages: [1]
Print
Jump to:  


DISCLAIMER
WE DONT HOST ANY ILLEGAL FILES ON THE SERVER
USE CONTACT US TO REPORT ILLEGAL FILES
ADMINISTRATORS CANNOT BE HELD RESPONSIBLE FOR USERS POSTS AND LINKS

... Copyright 2003-2999 Sonsivri.to ...
Powered by SMF 1.1.18 | SMF © 2006-2009, Simple Machines LLC | HarzeM Dilber MC