Sonsivri
 
*
Welcome, Guest. Please login or register.
Did you miss your activation email?
March 28, 2024, 09:21:37 21:21


Login with username, password and session length


Pages: [1]
Print
Author Topic: cheap PLL or DDS or else  (Read 8880 times)
0 Members and 1 Guest are viewing this topic.
Jeckson
Active Member
***
Offline Offline

Posts: 110

Thank You
-Given: 54
-Receive: 6



« on: December 19, 2009, 04:15:08 16:15 »

Hai

I'm looking low cost PLL or DDS or else(flexible oscillator controlled) which controlled with MCUs or PC.
working in VHF range...

Someone have info's where's to find low cost that kind ICs...

Thank's
Jeckson
Logged
LabVIEWguru
Senior Member
****
Offline Offline

Posts: 300

Thank You
-Given: 270
-Receive: 593



« Reply #1 on: December 20, 2009, 04:23:53 04:23 »

Analog Devices website has much DDS data in PDF format. Most of the DDS devices can be used in either serial (SPI) or parallel interfaces. Several of their DDS devices work in the 300 Mhz+ range. They also have application notes on designing output filters and amplifiers. I don't know what country you are in, but if you have an Analog Devices representative in your country they will probably sample you the device you need. You'll also need an oscillator to drive the DDS. It probably would be easier & less cost to build an oscillator for near the frequency you need then mix it with the DDS output. Also in the magazine section here in "QEX" there are a number of DDS construction articles. 
Logged
nawab
Newbie
*
Offline Offline

Posts: 23

Thank You
-Given: 15
-Receive: 4


« Reply #2 on: December 20, 2009, 08:56:36 08:56 »

Look  out for Silicon Labs Si 570 series progrmmable clock chips. Cypress also has similar stuff.
Logged
Jeckson
Active Member
***
Offline Offline

Posts: 110

Thank You
-Given: 54
-Receive: 6



« Reply #3 on: December 20, 2009, 01:44:11 13:44 »

Hai

Thank's for response..

I knew that there's some DDS from Analog and Si 570...

But still cost...they around 10US$ each.
Meanwhile I'm looking in 1-3 US$/pieces with Xty(10 to 99) quantities.

Thank you
Jeckson
Logged
Alienbeing
Active Member
***
Offline Offline

Posts: 164

Thank You
-Given: 68
-Receive: 45


« Reply #4 on: December 22, 2009, 03:27:23 03:27 »

I have been using a DDS Kit from here.  Works good from 1 to 70 mhz.
http://www.amqrp.org/kits/dds60/

Very nice quality DDS kit. I have interfaced this kit with a PIC and added an encoder and keypad for frequency selection, and LCD display to show the output frequency. I have also written a Delphi application that is interfaced through a USB to rs232 FTDI IC that allows me to control the frequency output to the DDS with my laptop with gives the best accuracy. Reason for better accuracy is the ability of the PC to perform better floating point math operations when calculating the control codes for the DDS.
You will not be disappointed with this module (kit) I have bought 3 of them already.

« Last Edit: December 22, 2009, 03:32:39 03:32 by Alienbeing » Logged
lab
Newbie
*
Offline Offline

Posts: 12

Thank You
-Given: 18
-Receive: 7


« Reply #5 on: December 22, 2009, 09:21:01 09:21 »

this is my controller DDS developed Poton PicBasic. I hope you can interest.
Ciao Francesco
lab
Logged
LabVIEWguru
Senior Member
****
Offline Offline

Posts: 300

Thank You
-Given: 270
-Receive: 593



« Reply #6 on: December 23, 2009, 06:27:20 06:27 »

I was just thinking - some of the 1st DDS used an EPROM with a sine/cosine table programmed into it. I'm sure you changed the step size & speed. You have to research this and find the magazines the articles are in.
Logged
Jeckson
Active Member
***
Offline Offline

Posts: 110

Thank You
-Given: 54
-Receive: 6



« Reply #7 on: December 28, 2009, 02:35:57 14:35 »

Hai
Thank you very much

>this is my controller DDS developed Poton PicBasic. I hope you can interest.
>Ciao Francesco

Where's the schematic picture...DSN works with another program(Is that with Workbench?),Have very old workbench and protel and seems didn't work with PIC18F452.
Also here's the download time very long....Kindly with schematics picture.

>I was just thinking - some of the 1st DDS used an EPROM with a sine/cosine table programmed into it. I'm sure you changed the step >size & speed. You have to research this and find the magazines the articles are in.

We have similiar thought...Yes something like parts that available here.
Like PLL 4046,EPROM,etc.

my problem at red circle...

Logged
bobcat1
Senior Member
****
Offline Offline

Posts: 295

Thank You
-Given: 4135
-Receive: 89


« Reply #8 on: February 20, 2010, 01:42:09 13:42 »

Hi

Elektor electronics have an article on DDS using an FPGA last year - Dont remember the month

On there site there is a VHDl code for the FPGA

Down load the code and implement it on an ACTEL low cost (sub 1$) FPGA to get into the VHF rang

Actel FPGA can work up to 300MHz

to keep it low cost use a R2R and an opamp as an D2A solution

You cam also implement an oscillator using an inverter and a resistor on the FPGA

All the best

Bobi    

« Last Edit: February 20, 2010, 01:44:26 13:44 by bobcat1 » Logged
marianqt
Newbie
*
Offline Offline

Posts: 14

Thank You
-Given: 2
-Receive: 4


« Reply #9 on: February 21, 2010, 04:56:46 16:56 »

Look here: http://www.rfcandy.biz/shop/ search for LMX2306,LMX2330 or LMX2322 in his site. These are great circuits for RF-PLL and are very cheap.
Logged
Pages: [1]
Print
Jump to:  


DISCLAIMER
WE DONT HOST ANY ILLEGAL FILES ON THE SERVER
USE CONTACT US TO REPORT ILLEGAL FILES
ADMINISTRATORS CANNOT BE HELD RESPONSIBLE FOR USERS POSTS AND LINKS

... Copyright © 2003-2999 Sonsivri.to ...
Powered by SMF 1.1.18 | SMF © 2006-2009, Simple Machines LLC | HarzeM Dilber MC