Sonsivri
 
Home Contact Us Help Search GoogleTagged Donations Login Register
*
Welcome, Guest. Please login or register.
Did you miss your activation email? 		May 01, 2025, 02:26:14 14:26


Login with username, password and session length


Sonsivri > Electronics > AVR, 8051 Family and ARM Area (Moderator: bbarney) > USB programmer schematic needed for ATMega8......!!!
Pages: [1]
« previous next »
Print
Author Topic: USB programmer schematic needed for ATMega8......!!!  (Read 10910 times)
0 Members and 1 Guest are viewing this topic.
Tahmeed
Newbie
*
Offline Offline

Posts: 21

Thank You
-Given: 21
-Receive: 0
« on: January 06, 2011, 06:51:55 06:51 »
hello every1.......
I'm a beginner in uC programming.. Cool I wanna start with AVR's ATMega8 IC.. so pls recommend me a useful and easy to make, cheap programmer circuit schematic for USB port...I'll try to make it myself..
N.B........I have intel DG31 motherboard in pc which includes 1 serial port + 6 USB ports..... I wanna use USB...... Smiley
Logged
KhepeleSibilo
Translator
Junior Member
***
Offline Offline

Posts: 53

Thank You
-Given: 3
-Receive: 412


WWW
« Reply #1 on: January 06, 2011, 07:05:22 07:05 »
http://www.fischl.de/usbasp/
Logged
metal
Global Moderator
Hero Member
*****
Offline Offline

Posts: 2420

Thank You
-Given: 862
-Receive: 678


Top Topic Starter
« Reply #2 on: January 06, 2011, 07:24:32 07:24 »
and it works fine. You have to use the zener diodes on D-/+ in order for the PC USB ports to recognize USBasp without problems.

regards
Logged
Tahmeed
Newbie
*
Offline Offline

Posts: 21

Thank You
-Given: 21
-Receive: 0
« Reply #3 on: January 09, 2011, 06:15:29 18:15 »
please can now i have an programmer schematic for ATMega32.......
 i think this is better than atmega8.......with more flash memory......pls share d link...... Cheesy
Logged
metal
Global Moderator
Hero Member
*****
Offline Offline

Posts: 2420

Thank You
-Given: 862
-Receive: 678


Top Topic Starter
« Reply #4 on: January 09, 2011, 06:28:34 18:28 »
USBasp supports many AVR chips. Where did you read that USBasp doesn't support programming ATmega32?
Logged
DarkClover
Active Member
***
Offline Offline

Posts: 167

Thank You
-Given: 37
-Receive: 60


Still alive...
« Reply #5 on: January 17, 2011, 11:08:34 23:08 »
With USBprog you can program many different devices.
Therefore if you plan to extend the controller family later when you got into
all the AVR stuff this one would be perfect.

You can build it by yourself and it's open source.

Link: USBprog

Greets DarkClover
Logged
Not thinking means to believe what others say!
TRY & ERROR... the fundamental principle our existence is based on
pak
Junior Member
**
Offline Offline

Posts: 61

Thank You
-Given: 5
-Receive: 17
« Reply #6 on: January 22, 2011, 05:07:21 05:07 »
If you are using C or C++ program with WINAVR then just buy Arduino board and save a lot of time and money. Check the component list of arduino for BOM. If you really want to build yourself, visit this site and get schematic and firmware as well. http://arduino.cc/en/Main/Hardware . It supports Mega8, 16, 324, 1280 and 2560.

Happy MCU Programming!
pak
Logged
Tahmeed
Newbie
*
Offline Offline

Posts: 21

Thank You
-Given: 21
-Receive: 0
« Reply #7 on: January 22, 2011, 01:55:53 13:55 »
actually i found an circuit......hrre.........http://www.fischl.de/usbasp/.....but there was written that it is for atmega 8 n 48.... Roll Eyes... so i thought that it wont work for 32...... Cheesy
Logged
microkid
Active Member
***
Offline Offline

Posts: 129

Thank You
-Given: 45
-Receive: 23
« Reply #8 on: January 22, 2011, 02:18:11 14:18 »
Quote from: Tahmeed on January 22, 2011, 01:55:53 13:55
actually i found an circuit......hrre.........http://www.fischl.de/usbasp/.....but there was written that it is for atmega 8 n 48.... Roll Eyes... so i thought that it wont work for 32...... Cheesy

It works. I am using usbasp to program atmega32.

I think you misunderstood. The firmware is written for 8 and 48, but it can program most of the avr chips
Logged
Never Never Never giveup
DarkClover
Active Member
***
Offline Offline

Posts: 167

Thank You
-Given: 37
-Receive: 60


Still alive...
« Reply #9 on: January 23, 2011, 06:53:40 18:53 »
Yeah it can be changed to almost every other AVR chip. I use a ATtiny2313 (the code needs a little bit of change)
and it works very well. My board is built completely out of SMD and fits into an USB flash drive case.

If you want, you can implement some status led's. They are quite handy to find errors during the programming.
Logged
Not thinking means to believe what others say!
TRY & ERROR... the fundamental principle our existence is based on
scrts
Newbie
*
Offline Offline

Posts: 24

Thank You
-Given: 12
-Receive: 11
« Reply #10 on: January 26, 2011, 02:38:05 02:38 »
I vote for STK500 from tuxgraphics. Works great, programming available directly from AVR Studio, no need of avrdude/ponyprog, really fast and handy.
Logged
ambo
Newbie
*
Offline Offline

Posts: 23

Thank You
-Given: 127
-Receive: 6
« Reply #11 on: May 17, 2011, 03:47:21 15:47 »
Try USB AVR LAB  http://wiki.ullihome.de/index.php/USBAVR-ISP/de.  It can also function as a simple dev. board aside from being a h/w programmer that can easily be changed from avrispmkii, jtagicemkii or usbasp.  Oh and it uses an atmega8.  I used an atmega8L with a 12 MHz crystal.
Logged
Tahmeed
Newbie
*
Offline Offline

Posts: 21

Thank You
-Given: 21
-Receive: 0
« Reply #12 on: June 20, 2011, 05:11:00 17:11 »
thanx to everyone for your kind help... Smiley   i think usbasp will be easiest for me to build...
Logged
Pages: [1]
Print
« previous next »
Jump to:  


DISCLAIMER
WE DONT HOST ANY ILLEGAL FILES ON THE SERVER
USE CONTACT US TO REPORT ILLEGAL FILES
ADMINISTRATORS CANNOT BE HELD RESPONSIBLE FOR USERS POSTS AND LINKS

... Copyright © 2003-2999 Sonsivri.to ...
 Powered by SMF 1.1.18 | SMF © 2006-2009, Simple Machines LLC | HarzeM Dilber MC