| Country | India |
| Note | I am in the field of electronics and programming for more than 30 years. I started by freelance repairing electronic circuits then switched to PIC Micro controller programming. Still doing repair and programming but most of the time spends in programming. I consider it as a joyful (even though some times painful) creative work rather than a job. I think sharing experiences will become beneficial to all in one day or in another day. |
|
51
on: April 02, 2024, 07:08:07 07:08
|
||
| Started by MicroCat - Last post by MicroCat | ||
|
|
||
|
52
on: April 01, 2024, 09:11:34 21:11
|
||
| Started by pickit2 - Last post by Wizpic | ||
|
Which is the better controller out of the 2 shown on here ?
Or any recommended descent usb controller that does not have to convert to parallel port (has these don’t exist anymore) Also I know you really or possible to say which is the better software out of these two, I know Mach 3 is really good but it’s so old now and not moved forward in years. I’ve seen Mach4 but not seen a cracked version may be I can try the demo of it and would have to look into which controller is supported Thanks |
||
|
53
on: April 01, 2024, 06:38:44 18:38
|
||
| Started by sphinx - Last post by sphinx | ||
|
here are the gerbers, to me those look a bit weird compare to those mae with ad
i git some issues using those in ad |
||
|
54
on: April 01, 2024, 04:40:12 16:40
|
||
| Started by sphinx - Last post by Sideshow Bob | ||
|
I am going to try repair my onkyo before building something, i just wanted to try this method of If you find the Gerber file for this design. You could try reverse engineer using this method. rev eng of making a pcb so that whay i made this https://www.youtube.com/watch?v=j3MgdCoAoiU The Gerber file can be downloaded from Elektor. But that requires paid membership (Green or Gold) I am working recreating the schematics. I am almost done with amp part |
||
|
55
on: April 01, 2024, 09:40:07 09:40
|
||
| Started by nullos - Last post by PIC_dude | ||
|
The new version v5.117 is now available, for those of us who had problems with the SPI of the new PIC18... it seems that this version will solve it! Can you put the link? Or maybe cjack? Please!  |
||
|
56
on: March 31, 2024, 09:45:39 21:45
|
||
| Started by Manuel - Last post by mars01 | ||
|
Happy Easter!
|
||
|
57
on: March 31, 2024, 09:00:51 09:00
|
||
| Started by Manuel - Last post by Manuel | ||
|
Enjoy the dayz.
X! |
||
|
58
on: March 31, 2024, 08:33:10 08:33
|
||
| Started by jenkinelec - Last post by jenkinelec | ||
|
Thank you for invitation. Registration is done.
Note: This message sent by the system behalf of jenkinelec. |
||
|
59
on: March 30, 2024, 11:08:19 23:08
|
||
| Started by jenkinelec - Last post by Checksum8 | ||
|
This member is invited by me. Registration isn't completed yet.
Note: This message sent by the system behalf of Checksum8. |
||
|
60
on: March 30, 2024, 04:48:16 16:48
|
||||||
| Started by jenkinelec - Last post by jenkinelec | ||||||
|
||||||